"Nobody who has succeeded has not failed along the way"
Arianna Huffington
Read the first 10% of my books "Didymus" and "The BEAST of BIKO BRIDGE" for free
You can also read and download 100% free my short stories "A Real Surprise" and "Pieces of Eight" at
http://www.smashwords.com/books/view/332256
tec0 (16-Apr-12)
If you're installing a timer on a 200litre cylinder I would be very careful about using makes and models in the lower price bracket. There's a lot of R170.00 timers around that aren't capable of reliably switching a 4KW element even though they are rated to 16A which is only marginally less than a 4Kw linear load.
_______________________________________________
_______________________________________________
I can see a new Paper 1 question
How much electricity can the consumer save if supplied by a 10000/230V at a power factor of 95% if:
1 x 150l kW Water Heater
12 x Energy saving 15W globes
Etc
He he
the geyser is a resitive load ...so it has a PF of 1 = 100%
the lamps however...being such a small load wouldnt really make an impact...even though i am yet to find one with a better PF than 0.25 ie 25 % efficency...tested with a fluke 435 PQA...i know from previous posts...someone did mention that you do get energy savers with a better PF.
my concern is the 500 million (just a wild guess) energy saver lamps being given away by eskom...what PF they have and what effect it has on the main grid...the question is...did eskom do a proper survey on the impact...millions of these energy efficient lamps would have on their system....considering all the other electronic devises being plugged into the system as modern technology booms...and did they take into account for harmonics...will there be penalties introduced in the future...like toll roads to make more money out of us...to cover up for their lack of planning.
it sounds like we will be paying for their inefficencies once again...thru increased water accounts to the tune of i think they mentioned 500 billion rand.
Many of the newer generation of compact fluorescents have built-in PF correction.....to a point at least. Cheap nasty normal tube type fluorescent fittings are probably the worst culprit for poor PF.
Switch mode power supply units are the scum of electrical demand management. They're dirty, filthy things with poor power factor and they produce large harmonics especially in the triplen range which cause increased neutral loads. These things are used in just about every home or office computer, they're also in laptop chargers, cellphone chargers....the list is endless. These SMPS's are a major cause of unnecessary load on the electrical supply system.
The easiest way to penalise customers for poor power factor is to use smart metering and make KVAr the billing unit instead of Kilowatt hours.
_______________________________________________
_______________________________________________
Geyser timers: I have found prices that vary from R240.00 for an entry level device to more than a R1000.00 for upmarket devices. I have had an "el cheapo" on my geyser for some years now, and have through instrumentation proved a saving of about 23% on geyser power only - for a house of two. Savings are of course totally dependant on the "on-off" cycle times that you decide upon. So I reackon it has been worth my while. An interesting Eskom project, go to Google and type in "Eskom's Residential Mass Roll-out" - this is an extremely interesting power conservation project, with freebies and rebates from Eskom.
Remember, if you have any electrical power saving devices fitted in your house, be cognisant of the fact that they should be SABS approved, or have IEC certification - furthermore they must be installed by a licenced electrician and you must demand a COC (Certificate of Compliance) saying that the installation complies the recommended wiring code. Otherwise in event of an insurance claim you will be in trouble.
All noted, AndyD, are you saying that a qualified spark is not necessary, or are you saying that a COC is not necessary depending on where the timer is located and wired? Would like to know more.
Right, here is my headache. Any sugestions, with brand names of equipment to employ?
House 1
House 2
~Expenses will eat you alive! - My first Boss~
The timer would be required to be installed by a competent person.
If for example the timer is installed in an enclosure that is secured to the cylinder itself with a very short cable between the enclosure and the cylinder element then the timer would be considered an integral part of the geyser and wouldn't necessarily fall under the scope of a COC.
If the timer was installed in the DB then it would fall under the scope of the COC and a certificate would need to be issued specifically for its installation.
@IMHO^^^
The installation at both premises is a shambles. I would rip it out and start again.
- No earth bonding visible on any cylinders
- Internal PVC cable used externally in view of the sun
- No spreg between the isolators and the cylinders (maybe the horozontal one does but it looks broken plus it's PVC in sunshine)
- Isolators inadequately IP rated
- Cabes un-secured
- Cables run in close proximity to or even strapped to hot water pipes
- No pipes fitted to the hot water safety valves (hope no kids play in this area)
- Looks like there might be a vac valve or two missing
- No trays installed under cylinders
- Some pipework insulation wouldn't go amiss but this isn't a legal issue.
- A couple of the cylinders have limescale streaks down them which is a sign or water leaks.
There's probably a few more things if I had time to study the pics properly.
_______________________________________________
_______________________________________________
Did you like this article? Share it with your favourite social network.