Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: Down Lighters flickering

  1. #1
    New Member
    Join Date
    Mar 2015
    Location
    Blouberg
    Posts
    4
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Down Lighters flickering

    Hi,

    Quick question to anyone that knows the answer.

    I have an outside patio section at home with around 10-12 down lighters connected to two different dimmer switches, one is in my room and the other is on the patio, recently the down lighters started flickering like strobe lights when turned on, no matter what brightness setting you choose.

    Any ideas on what causes this and what the solution would be.

    Thanks

  2. #2
    Diamond Member AndyD's Avatar
    Join Date
    Jan 2010
    Location
    Cape Town
    Posts
    4,938
    Thanks
    582
    Thanked 938 Times in 759 Posts
    Are the lamps LED? Is it a 2-way switch setup where you can switch all the lights on and off from either location or is it 2 separate circuits?

    Could be a dimmer problem or could be a poor wire termination somewhere. If it's the first then it's just an annoyance, if it's the latter it could be a fire hazard. I'd suggest get an experienced sparky to check the circuit and repair.
    _______________________________________________

    _______________________________________________

  3. #3
    New Member
    Join Date
    Mar 2015
    Location
    Blouberg
    Posts
    4
    Thanks
    0
    Thanked 0 Times in 0 Posts
    No its not the LED ones it those standard old school ones, and yes you turn them all on or off from either switch, It always used to work fine until one night it just started flickering, could it be possible that both the dimmer switches have packed up though, also keep in mind i live like almost on the beach, so corrosion is plentiful. I was told once that it could be the dimmer switch but removed the one switch which i thought could be faulty but it still goes off like a strobe on the other switch.
    I think getting a sparky out good, but as you know being a man you always like to try fix things first.

  4. #4
    Diamond Member AndyD's Avatar
    Join Date
    Jan 2010
    Location
    Cape Town
    Posts
    4,938
    Thanks
    582
    Thanked 938 Times in 759 Posts
    Are the switches of the 'bell-press' type where you push them and the naturally spring back?
    _______________________________________________

    _______________________________________________

  5. #5
    New Member
    Join Date
    Mar 2015
    Location
    Blouberg
    Posts
    4
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Yip those exact ones, it looks like a normal light switch, which you push on the bottom of the switch and then it springs back to like an off position, and then you hold it in to change the intensity of the light.

  6. #6
    Diamond Member AndyD's Avatar
    Join Date
    Jan 2010
    Location
    Cape Town
    Posts
    4,938
    Thanks
    582
    Thanked 938 Times in 759 Posts
    It's probably the 4-wire dimmer that's faulty but good luck locating it if it's not tucked away in one of the switch back boxes. If you replace the dimmer and there's still flickering it's time to get a sparky to run some tests and find the bad connection.
    _______________________________________________

    _______________________________________________

  7. #7
    Diamond Member
    Join Date
    Apr 2010
    Location
    planet earth
    Posts
    3,943
    Thanks
    153
    Thanked 317 Times in 287 Posts
    Chances are pretty good that it is a clipsal dimmer, if so throw them away and make sure you fit an R&D dimmer. Clipsal dimmers are absolute rubbish. Just make sure the right size dimmer is fitted.

    It sounds like you need to get an electrician to replace them.

  8. Thanks given for this post:

    DieterT (23-Mar-15)

  9. #8
    New Member
    Join Date
    Mar 2015
    Location
    Blouberg
    Posts
    4
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hahaha, ya I think a sparky is in order, thanks for all the help and advice.

  10. #9
    Bronze Member
    Join Date
    Oct 2014
    Location
    Pretoria
    Posts
    126
    Thanks
    16
    Thanked 16 Times in 15 Posts
    From all the dimmet transformers I have used I have found the Clipsal and International Lighting to be the most inconsistant that there are more faulty ones than working ones. Also just bare in mind that the transformer could be leading or trailing edge and when using LED globes on dimmers with locators be sure to use the anti flicker module you have to add inline

    "I used to have a lot of anger issues, now I just have a passion for justice"

  11. #10
    Bronze Member
    Join Date
    Oct 2014
    Location
    Pretoria
    Posts
    126
    Thanks
    16
    Thanked 16 Times in 15 Posts
    Ps : are you using 12v hologen globes the ones with the transformer with the pins at end of globe or 220v hologen the ones with the harness and stud ends?

    "I used to have a lot of anger issues, now I just have a passion for justice"

Page 1 of 2 12 LastLast

Similar Threads

  1. Monitor flickering colours
    By Streamline Imports in forum Technology Forum
    Replies: 4
    Last Post: 09-Jun-12, 12:05 AM
  2. Flickering LED problem
    By skatingsparks in forum Electrical Contracting Industry Forum
    Replies: 13
    Last Post: 23-May-11, 07:27 PM

Did you like this article? Share it with your favourite social network.

Did you like this article? Share it with your favourite social network.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •