Page 1 of 3 123 LastLast
Results 1 to 10 of 29

Thread: Mastech 5908C Multifunction Tester (Lite)

  1. #1
    Diamond Member AndyD's Avatar
    Join Date
    Jan 2010
    Location
    Cape Town
    Posts
    4,923
    Thanks
    576
    Thanked 934 Times in 755 Posts

    Mastech 5908C Multifunction Tester (Lite)

    Mastech 5908C 'Circuit Analyzer'

    Price; Under a grand ZAR.

    Looks like this;

    Click image for larger version. 

Name:	02.jpg 
Views:	242 
Size:	25.0 KB 
ID:	7209

    Tests performed;

    • True RMS
    • Ground to Neutral Voltage
    • Peak Voltage
    • Frequency
    • 5A/8A/10A load for volt
    drop test
    • Socket test function
    • RCD / GFCI test
    Line Volts: 85 - 265V
    Neutral/Ground: 0 - 10V
    Peak: 121 - 374V
    Freq: 45 - 65Hz
    Volt Drop: 0.1 - 99.9%
    RCD trip time: 1ms - 6.5s
    RCD trip Amp 30mA
    GFCI trip time: 1ms - 6.5s
    GFCI trip Amp: 6mA

    Has anyone got any first hand experience of this tester? I have a Mastech multimeter with logging that I use on my repair bench, it's a couple of years old, always been accurate and recently passed a calibration. The input stage on the multimeter isn't as well protected as a Fluke for example, it's classed as CATIII but lacks in physical separation and fuse quality. That said I'm aware of its limitations and only use it for electronics benchwork.

    The 5908C does an impressive array of tests and given the price it would be rude not to buy one if it does what it says. Just wondered if anyone had any advice about whether it's fit for purpose.

    MS5908C.pdf
    _______________________________________________

    _______________________________________________

  2. Thank given for this post:

    ACEsterhuizen (15-Aug-19), Trevor Varner (08-Sep-20)

  3. #2
    Site Caretaker Dave A's Avatar
    Join Date
    May 2006
    Location
    Durban, South Africa
    Posts
    22,646
    Thanks
    3,304
    Thanked 2,676 Times in 2,257 Posts
    Blog Entries
    12
    It looks like you'll have to be our tester, Andy.

    I have to say it does look interesting...

  4. #3
    Diamond Member AndyD's Avatar
    Join Date
    Jan 2010
    Location
    Cape Town
    Posts
    4,923
    Thanks
    576
    Thanked 934 Times in 755 Posts
    Already ordered last week, will keep you posted.
    _______________________________________________

    _______________________________________________

  5. #4
    Diamond Member AndyD's Avatar
    Join Date
    Jan 2010
    Location
    Cape Town
    Posts
    4,923
    Thanks
    576
    Thanked 934 Times in 755 Posts
    Okay, as of this afternoon I'm the proud owner of a brand new Mastech 5908C 'Circuit Analyzer'.

    Contained in the box is;
    1x Zip pouch
    1x Instruction booklet (identical to the pdf in the post above)
    1x Mastech 5908C tester
    6x AAA batteries
    1x Test lead with a 10Amp IEC 60320 plug on one end (computer type plug) and a 16Amp Schuko plug on the other end.

    Why it comes with a Schuko plug on the lead I can't imagine, as far as I know schuko sockets aren't even legal in South Africa.


    Click image for larger version. 

Name:	a.jpg 
Views:	220 
Size:	31.0 KB 
ID:	7215
    _______________________________________________

    _______________________________________________

  6. #5
    Diamond Member AndyD's Avatar
    Join Date
    Jan 2010
    Location
    Cape Town
    Posts
    4,923
    Thanks
    576
    Thanked 934 Times in 755 Posts
    Removing the battery cover and another 4 screws on the reverse side of the tester the entire back easily separates to reveal the single circuit board inside.

    Click image for larger version. 

Name:	b.jpg 
Views:	255 
Size:	69.2 KB 
ID:	7216

    A considerable spiral of plactic came out with two of the back panel screws which appear to just self-tap into the posts on the front panel and on later reassembly one of the screws didn't tighten fully.

    The internal circuit board looks fairly neat at first glance, all the components are SMD with no through-hole components that I've seen in abundance on cheaper testers in the past. There's numerous empty solder pads scattered around the board along with a solid plastic blanking plug on the LHS of the tester where a button might go which suggests there's at least one more model available in this form factor with extra components and probably extra tests it can do.

    The soldering on the input pins is borderline passable at best and there's no slots cut into the circuit board to create safety separation between the input area and the logic area of the board. The input fuse looks like it might be silica filled but it's small and of poorer quality than the HRC fuses you get in more expensive testers. Also there's only a single fuse and a very small surge arrestor by the looks of it and there's no containment panels molded into the back panel to surround the fuse and the MOV to contain any flash that might occur should they ever blow.

    According to the literature the rating of the tester is IEC 601010-1, 300v, CAT III. I'd probably be happy to use the tester on single phase domestic circuits but the safety of the input stage doesn't instill much confidence and I'd be loathed to use it anywhere with higher than average PFC, anywhere where there may be high voltage transients or where there could be any chance the 300v limit might be accidentally exceeded.
    _______________________________________________

    _______________________________________________

  7. #6
    Diamond Member AndyD's Avatar
    Join Date
    Jan 2010
    Location
    Cape Town
    Posts
    4,923
    Thanks
    576
    Thanked 934 Times in 755 Posts
    The input stage of the tester also has a large 5 Watt resistor which is mounted on top of a small chip. I'd guess the resistor is for performing the voltage test with a 5A, 8A and 10A load and the chip underneath it is for sensing over-temperature of the resistor which is going to heat up pretty quickly during this type of test. The resistor is sitting at an angle above the chip and there's a gap of a couple of milimeters between them. I'm not convinced about the effectiveness of this arrangement as protection against overheating, a thermal fuse would have been a nice addition here.

    Click image for larger version. 

Name:	c.jpg 
Views:	243 
Size:	59.8 KB 
ID:	7219


    Under the microscope it's easier to see the angle and distance of the components relative to each other;

    Click image for larger version. 

Name:	5.jpg 
Views:	256 
Size:	45.9 KB 
ID:	7218
    _______________________________________________

    _______________________________________________

  8. #7
    Diamond Member AndyD's Avatar
    Join Date
    Jan 2010
    Location
    Cape Town
    Posts
    4,923
    Thanks
    576
    Thanked 934 Times in 755 Posts
    A closer look at the board shows that there's several areas where the components were soldered on by hand. The quality of the soldering and the amount of residual flux and contamination is very poor.

    This is the MOV surge arrestor on the input stage;

    Click image for larger version. 

Name:	7.jpg 
Views:	239 
Size:	87.2 KB 
ID:	7220



    This is some of the SMD soldering under a microscope showing large amounts of contamination;

    Click image for larger version. 

Name:	6.jpg 
Views:	249 
Size:	77.9 KB 
ID:	7221 Gawd knows what all the black bits are...


    Click image for larger version. 

Name:	1.jpg 
Views:	273 
Size:	101.0 KB 
ID:	7222 I'd be interested to know if R16 is supposed to be there....


    Click image for larger version. 

Name:	2.jpg 
Views:	241 
Size:	100.8 KB 
ID:	7223
    _______________________________________________

    _______________________________________________

  9. #8
    Diamond Member AndyD's Avatar
    Join Date
    Jan 2010
    Location
    Cape Town
    Posts
    4,923
    Thanks
    576
    Thanked 934 Times in 755 Posts
    So.....to sum up so far, I guess you get what you pay for.

    On the down side it's got minimal, probably borderline passable user protection. The general build quality and ruggedness is average until you get down to component level on the board when it becomes unacceptably poor and it comes with a plug that's not relevant in this country.

    On the up side is it's low price and wide range of tests it can apparently do.

    I'll get around to doing some tests with it this weekend and report back again.
    _______________________________________________

    _______________________________________________

  10. #9
    Bronze Member
    Join Date
    Mar 2018
    Location
    Western Cape
    Posts
    120
    Thanks
    11
    Thanked 15 Times in 14 Posts
    Morning Andy

    Thank you for the on depth feedback so far. Very interested in the update on the testing.

  11. #10
    Site Caretaker Dave A's Avatar
    Join Date
    May 2006
    Location
    Durban, South Africa
    Posts
    22,646
    Thanks
    3,304
    Thanked 2,676 Times in 2,257 Posts
    Blog Entries
    12
    Quote Originally Posted by AndyD View Post
    Gawd knows what all the black bits are...
    Flux?
    (Kinda reminds me of my early soldering days )

Page 1 of 3 123 LastLast

Similar Threads

  1. Multifunction Testers
    By IMGREG in forum Electrical Contracting Industry Forum
    Replies: 4
    Last Post: 28-Jan-18, 11:29 PM
  2. Corsa Lite
    By HR Solutions in forum Local Ads on TFSA
    Replies: 4
    Last Post: 09-Apr-15, 05:51 PM
  3. [Question] Neotel Lite
    By AmithS in forum Technology Forum
    Replies: 0
    Last Post: 27-Oct-09, 07:49 PM
  4. Lite skin for dial-ups or to reduce page download size.
    By Dave A in forum Administrative issues
    Replies: 9
    Last Post: 08-Jul-08, 10:12 PM
  5. Jonas Savimbi's Money comes to lite
    By Vincent in forum Scam Alert Forum
    Replies: 1
    Last Post: 07-Jan-08, 07:08 AM

Did you like this article? Share it with your favourite social network.

Did you like this article? Share it with your favourite social network.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •