Results 1 to 8 of 8

Thread: Lightning arrester testing

  1. #1
    Site Caretaker Dave A's Avatar
    Join Date
    May 2006
    Location
    Durban, South Africa
    Posts
    22,648
    Thanks
    3,304
    Thanked 2,676 Times in 2,257 Posts
    Blog Entries
    12

    Lightning arrester testing

    Any ideas on how to test that a lightning arrester is still working?

  2. #2
    Diamond Member tec0's Avatar
    Join Date
    Jun 2009
    Location
    South Africa
    Posts
    4,624
    Thanks
    1,884
    Thanked 463 Times in 410 Posts
    Blog Entries
    3
    Well you get a lot of lighting arresters. In the aria where I live we get massif lighting strikes, sometimes so powerful that they take out the power in really no time at all. I think it’s because of all the dust. So unplugging everything is probably your only bet.

    So the real question is what type of lighting arrester are you using at the moment?
    peace is a state of mind
    Disclaimer: everything written by me can be considered as fictional.

  3. #3
    Gold Member garthu's Avatar
    Join Date
    Dec 2008
    Location
    Midrand
    Posts
    595
    Thanks
    39
    Thanked 65 Times in 55 Posts
    A key and a kite were the first thing that came to mind

    Are we talking domestic TV type stuff?? The easiest is visual. If the MOV's are not damaged/cracked etc..they then it should be fine. If the MOV's have any continuity they are stuffed.

    Only other way is get a current limited AC supply 300V variac or such and see if it starts limiting at around 250V (or the MOV's limits)

    Fence lightning protectors are if theres any continuity, its stuffed.
    Garth

    Electric fence Installation : www.midrand-electronics.co.za
    Free Classified Adds : www.bgone.co.za

  4. #4
    Site Caretaker Dave A's Avatar
    Join Date
    May 2006
    Location
    Durban, South Africa
    Posts
    22,648
    Thanks
    3,304
    Thanked 2,676 Times in 2,257 Posts
    Blog Entries
    12
    This would be the type that goes into an electrical distribution board.

  5. #5
    Diamond Member AndyD's Avatar
    Join Date
    Jan 2010
    Location
    Cape Town
    Posts
    4,923
    Thanks
    576
    Thanked 934 Times in 755 Posts
    Are they general purpose surge protectors?

    Some surge arrestors have an indicator led (or neon) which lights up if they need replacement.
    _______________________________________________

    _______________________________________________

  6. #6
    Site Caretaker Dave A's Avatar
    Join Date
    May 2006
    Location
    Durban, South Africa
    Posts
    22,648
    Thanks
    3,304
    Thanked 2,676 Times in 2,257 Posts
    Blog Entries
    12
    All the ones I've seen have an indicator of some sort. Of course not being on the service end that also means I haven't seen many

    Maybe I'm second guessing this or it's a broken telegraph problem, but the term used was "test" the lightning arresters. Now I took that as something different from running around checking the indicators. But I could be wrong.

    Do you think those indicators are reliable?

  7. #7
    Diamond Member AndyD's Avatar
    Join Date
    Jan 2010
    Location
    Cape Town
    Posts
    4,923
    Thanks
    576
    Thanked 934 Times in 755 Posts
    The end of life indicators on a DB mounted surge arrestor should be a reliable indicator. The cheap and nasty five into one trailing adapters with surge protection are a different story, I wouldn't trust those as far as I could throw them.

    Actual testing of surge arrestors is a little tricky. You need to know the clamping voltage and what type of arrestor it is. Also running a surge arrestor above the clamping voltage, even in a short test, can in itself cause the device to break down irreparably.

    MOS type arrestors should really be replaced as a matter of course when they reach 7-8 years of service. They are extremely sensitive to moisture and tend to have reached the end of their reliability at around this time.

    Thermal imagery can be use for the larger arrestors used in power transmission systems but I'm not sure if it would be effective for the small DIN mounted devices in a DB. Maybe Murdock or QuintonIR could clarify further.

    The definitive answer would be to consult the manufacturers literature for that model of device.
    Last edited by AndyD; 29-Sep-10 at 05:54 PM.
    _______________________________________________

    _______________________________________________

  8. Thanks given for this post:

    Dave A (29-Sep-10)

  9. #8
    Email problem Master Electrician's Avatar
    Join Date
    Jan 2010
    Location
    Cape Town
    Posts
    28
    Thanks
    3
    Thanked 33 Times in 12 Posts
    According to CBI (Circuit Breaker Industries) if the indicator is off when the power is on, the unit is stuffed.

Similar Threads

  1. Touch safe office equipment testing
    By Dave A in forum Electrical Contracting Industry Forum
    Replies: 1
    Last Post: 28-Sep-10, 11:39 PM
  2. [Question] Single phase and 3 phase testing course
    By skatingsparks in forum Electrical Contracting Industry Forum
    Replies: 3
    Last Post: 26-Feb-09, 09:14 AM
  3. [Article] 10 Steps to Testing the Viability of Your Online Business Idea That Won't Break the B
    By 3x-a-d3-u5 in forum General Business Forum
    Replies: 0
    Last Post: 02-Feb-09, 11:03 PM
  4. Driver testing backlog
    By Dave A in forum General Business Forum
    Replies: 0
    Last Post: 22-Jul-06, 07:36 AM

Tags for this Thread

Did you like this article? Share it with your favourite social network.

Did you like this article? Share it with your favourite social network.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •